How to Repair and Replace the Shower Drain

A leak of any sort in any pipe can be extremely disastrous for your home. So repair any leak as soon as you locate it. At times shower drain may sustain leak and need immediate repair lest the water penetrates into the floor and makes it way down to the foundation and eventually damaging the home badly. You can remove and replace the shower drain yourself with some effort and beforehand knowledge. But if you are amateur to this work, it is suggested to hire a plumber to replace the shower drain as soon as possible to prevent severe damage to your home.

Required Items

- ABS cement
- Plumber's putty
- Basket wrench
- Utility knife
- Slip coupling
- PVC pipe
- Shower drain
- Philips screwdriver
- Handsaw

Directions

1. Before begin, block the water supply line, which supply water to the shower.

2. Locate the drain pipes. You might have to tear off the flooring to uncover the pipes and to have better access to them. If you have access from below, you can work from below the bathroom. It depends on the position of the pipes.

3. Take a hacksaw and cut the part of the drain pipe that is leak or damage. In addition to this, you need to cut along the pipe further to remove this entire part of the pipe.

4. Take the drain away by cutting the silicone putty holding the drain with utility knife. Now open the drain cover by unfastening the screws with the help of Philips screwdriver. After removing the cover, take a basket wrench and take the drain away by turning the wrench anti-clockwise.

5. Insert the new drain into the specific place. Secure the new drain with plumber's putty.

6. Using the ABS cement, attach the PVC pipe to the new drain. ABS cement is a substance used to give the waterproof connection to the pipe and drain. You can inspect the pipe as well for any possible leaks. Replace the pipe if you notice any leakage in the pipe. If no leak spotted, then use the same pipe.

7. Connect the end of the existing pipe with the end of the new installed pipe. To connect the old and the new pipes you need to have a slip coupling of exactly the same size of pipes.

8. To secure the coupling, add glue on its both sides and put pipes into it.

9. Allow the putty to dry for many hours. Till then don't use the shower.

Tips & Precautions

-The best time to replace the drain is night time. Install the new drain and it will be ready for use till morning.
-In case you are having problem in replacing the drain, contact a plumber to do a repair work for you.

How to Repair and Replace the Shower Drain

Plumbers Putty

How to Repair and Replace the Shower Drain

How to Repair and Replace the Shower Drain
How to Repair and Replace the Shower Drain

Plumbers Putty

How Plumbers Replace Bathroom and Kitchen Sink Faucets

If you are considering upgrading your bathroom and kitchen sink faucets, you have come to the right place. The following explanation will make your task much easier and will save your time as well.

How Plumbers Replace Bathroom and Kitchen Sink Faucets

How Plumbers Replace Bathroom and Kitchen Sink Faucets

---

How Plumbers Replace Bathroom and Kitchen Sink Faucets

How Plumbers Replace Bathroom and Kitchen Sink Faucets

However, before we start, make sure that you have following materials ready with you.

- New faucet assembly

- Basin wrench

- Adjustable wrenches

- Slip-joint pliers

- Scouring pad

Now follow these simple steps. (Assuming that you are replacing the old two-handled faucet with the more modern single-handled type)

Replacing Kitchen Sink Faucets
1. Before you start, go at the shut-off valves under the sink, and turn off the water.

2. Open the faucet so that it could drain any excess water.

3. The next step is to disconnect the hot and cold water supply lines from the shutoff valves. You can use a small adjustable-wrench to do this.

4. Reach up behind the faucet. You will find the coupling nuts that connect the supply tubes to the faucet. Unscrew the same using a basin wrench.

5. Behind the faucet, you will also find mounting nuts that hold the faucet in place. Remove these nuts using the same basin wrench.

6. Now that you have disconnected the mounting nuts, you can lift out the old faucet. Lifting it out, disconnect the sprayer hose from the assembly using an adjustable wrench.

7. Lift out the sprayer hose, and remove the faucet.

8. Once you have removed the faucet, clean the surface of the sink thoroughly with a scouring pad.

9. Remove the escutcheon cap and replace the same with the one that is included with your new faucet.

10. Now you are ready to make the new connection. Bring your new sprayer hose, and slip it down through the sprayer hole.

11. Feed the sprayer hose up through the center faucet hole, and connect the hose through the sprayer nipple using an adjustable wrench.

12. If the hot and cold supply tubes of the new faucet have a different length, attach flexible connectors to the fittings on the supply tubes. Hold the faucet fitting stationary with one wrench and tighten each connection with another wrench.

13. Insert and feed the supply lines and the connectors into the center hole, and then seat the faucet.

14. Now crawl up under the sink and in order to hold the faucet in place, install a washer and nut to the end bolts.

15. First, tighten the nuts by hand, and then with a basin wrench.

16. Connect the supply lines to the shutoff valves, and turn the water on.

17. Turn on the faucet and check for leaks.

Replacing Bathroom Sink Faucets
1. Go underneath the sink. Turn off the water. Loosen the collar nuts on the drainpipe.

2. Drain any excessive water, and then remove the drainpipe.

3. Loosen the nuts that hold the pop-up assembly in place under the sink using slip-joint pliers.

4. Unscrew the pop-up flange in order to free the assembly underneath the sink.

5. Remove the fittings that join the supply lines of the old faucet to the shutoff valves, using a wrench.

6. Repeat the steps 4-15 as explained above for replacing kitchen faucet.

7. Now, you have to install the pop-up assembly.

8. Push the pop-up rod down through the body of the faucet.

9. Attach the flat bar.

10. At the bottom of the new flange, use a little plumber's putty to hold the tailpiece so that the whole assembly protrudes up through the drain hole in the sink.

11. Spin the ring to position the same with the tailpiece under the sink.

12. In order to secure pop-up housing in place, tighten the nut on top of the tailpiece.

13. Hook up the pop-up lever onto the flat bar in order to secure it to the pop-up housing.

14. Drop the stopper into the drain hole.

15. Replace the drainpipe.

16. Tighten the collar nuts.

17. Turn on the faucet and check for leaks.

Hence, replacing a kitchen and a bathroom faucet is almost similar except for the work related to the pop-up assembly that is included with the bathroom sink.

How Plumbers Replace Bathroom and Kitchen Sink Faucets