Tuesday, February 26, 2013

Skylights - A Homemade Shallow Box-Like Acrylic Condensation Cover for Dome Installations

Skylights - A Homemade Shallow Box-Like Acrylic Condensation Cover for Dome Installations



ItemTitle

Acrylic or polycarbonate dome skylights come is several sizes today. The traditional ones, however, are square to rectangular in shape, and run about 5" in height. Their width and length can be anywhere from 12" to 36", and are 1/8" thick.

These domes can be mounted onto wooden curbs (2x2" to 2x6"), around which the roof shingles are caulked or thin-metal flashed to prevent any rain leakage around them. These domes can also be surface mounted directly onto the tar paper and wooden sheeting directly beneath the shingles.

In the latter case, the dome's surrounding shingles themselves are directly laid over its flat outside flanges similar to the way the shingles are commonly laid over the flat metal of roof vents, furnace stacks, sewer vents and so forth. This installation minimizes the dome's height.

Problem. Either way, or no matter how the domes are mounted, they can and will produce unwanted condensation and similar leaks even if they have an inner plastic shield within them. These domes are also vulnerable to being cracked from large hail, fallen tree branches, earthquakes, or careless roofers. When these events happen, the skylights will leak rain water as well in addition to forming moisture.

Solution. Build and install a shallow-box-like 5-1/2"-high hard transparent cover over the dome on the roof. This cover will act like a storm window does by taking the brunt of temperature change and the formation of most condensation. For this article, a 20" square dome (which includes a 1" flange on each side of the 18"-square dome itself), 5" high, and surface mounted directly to the roof sheeting will be used as the example to be covered with the box-like storm cover. Similar covers can be built proportionally for other dome sizes.

Materials and tools (total cost for parts: -90, depending on the availability of the acrylic sheet).

One 2x6x96" pressure-treated board () One 22x22" sheet of heavy 0.22" thick acrylic plexiglass (-60, depending on the cut sizes available at the outlet). If the piece must be cut from a larger sheet, leave the protective films unpeeled on both sides of the sheet until the sawing is done. Use a sharp fine-tooth saw blade. Otherwise, let the outlet cut it to size for you. Twelve #12x3" Philips screws 20 to 30 - #8x1" Philips drywall screws (wide head) One small tube clear silicone caulk () Two tubes silicone window/door caulk similar in color to the roof shingles () Four perpendicularly flat 2-1/2" L-shaped brackets () Eight #10x1" wood screws (for attaching the L-brackets to the cover frame) Eight #10x1-1/2 to 2" wood screws (for attaching the frame's L-brackets to the roof through the shingles) One quart oil-base water-proof paint similar in color to the roof shingles () Tools: electric circular saw, electric drill, bits, Philips screwdriver, caulking gun, putty knife, rat-tail file, paintbrush

Cover construction.

1. Cut the 2x6" board into four square-cornered pieces: 2 22"-long ones and 2 19"-long ones.

2. Assemble the 22" square box-like frame by sealing/securing the four corners with the silicone window/door water-proofing caulk and 3" screws.

3. On what will be the lower-end of the bottom side, use the file to make at least three half-moon groves for moisture drainage.

4. Paint both the inside and outside of the wooden frame. Let dry.

5. Place the acrylic plexiglass flush over the frame.

6. Mark on the plexiglass where the screw holes will go, about 5" apart around the top of the frame.

7. At each mark, drill a hole through the plexiglass (only) wider than the drywall screw.

8. Then, by using a narrow bit, drill holes 1/2" deep into the wood frame dead-center through the plexiglass holes.

9. Remove the plexiglass from the frame, noting how it fits onto the frame.

10. Brush away any plastic or wood shavings from the frame and plexiglass.

11. With the silicone caulk, add a narrow bead lengthwise on each side of the frame's drill holes all around it.

12. Carefully replace the plexiglass atop the frame, aligning it to the original drill holes accordingly.

13. Install the screws to medium tightness, so not to crack the plexiglass. The caulk will flatten and spread between the plexiglass and the frame, sealing it.

14. Add at least one flat L-shaped bracket to each side of the frame flush to its bottom side with the 1" wood screws.

15. Paint the brackets.

Cover installation (the easy way).

1. While using safety precautions, carry the completed cover up to the roof, assuming the roof is a low-pitch and safe to walk on.

2. Center it over the dome skylight, square to square.

3. Attach the dome to the roof through the shingles with the 1-1/2 to 2" wood screws, depending on the thickness of the shingles.

4. Seal the bottom side of the upper end and both sides of the cover with the silicone window/door caulk. Seal the brackets and screws the same way. Leave the bottom side of the lower end unsealed for drainage. It is a storm window.

5. If necessary, touch-up the frame and brackets with paint.

By installing the cover atop the shingles, the wood sheeting beneath the shingles is also protected from any moisture damage. This placement also elevates the cover over the dome for adequate air space.

This cover will assume the formation of almost all the condensation that would otherwise occur within the dome, none of which will make it through the dome into the house nor beneath the shingles. It will also protect the dome from hail, fallen tree branches, and other damages. To learn more about skylight types and their maintenance, see these sites.


Skylights - A Homemade Shallow Box-Like Acrylic Condensation Cover for Dome Installations


Plumbers Putty



Plumbers Putty

Skylights - A Homemade Shallow Box-Like Acrylic Condensation Cover for Dome Installations



Skylights - A Homemade Shallow Box-Like Acrylic Condensation Cover for Dome Installations
Skylights - A Homemade Shallow Box-Like Acrylic Condensation Cover for Dome Installations

Plumbers Putty

Saturday, February 9, 2013

Garbage Disposal install

Garbage Disposal install



Samsung Galaxy

Tube. Duration : 9.72 Mins.



Garbage Disposal install



www.plumberx.comHello this is PlumberX. People always ask me what gave you the idea and what made you create these how to plumbing videos? Coming up with the idea was easy. After many years as a plumber and servicing customers at there home I've seen a lot of people in tuff situations, people that could not afford a plumber, people that didn't have time to wait for a plumber to come to there home and make repairs, hearing horror stories of Plumbers that have rip off costumers and gave bad service, to me this was a loud cry for help. One story come to mind; A friend of mine calls me and ask, PlumberX could you do me a favor and help this older lady that I know, and go by and look at her Plumbing, she needs plumbing work really bad but she's to scared to call a plumber because of the cost, and she know that if I send you over there to check out the plumbing she can trust me as a friend recommending you, sure I said I could do that. The next day came and I went to the older lady's home she came to the door with a pleasant smile very humble. I could see it in her eye's she didn't have to say a word ( What is this going to cost ) she was very polite and courteous. Sir would you like some thing to drink and I do appreciate you coming to check out my plumbing on such short notice. No problem mam, lets see what's going on here with your plumbing. This way Sir in the kitchen. As I walk through the home I saw in the corner of my eye younger children around 3, 5 and 6 years of age ...

Garbage Disposal install

Garbage Disposal install


Garbage Disposal install

Garbage Disposal install

No URL Garbage Disposal install

Handling Your Own Shower Drain Installation Project


Samsung Galaxy
ItemTitle

Upgrading a bathroom is one of the more popular home improvement projects. Handling the plumbing for draining your shower can be exceedingly simple unless you go overboard.

Whether you are a bathtub or shower person, most people look for shower only options when buying a home. This simple fact means more than a few homeowners spend a weekend upgrading or installing showers in their bathrooms. Fortunately for you, it is a fairly simple process.

A collector or pan refers to the horizontal surface located at the bottom of the shower. The collector typically consists of a non-slip surface slightly banked towards the center or wherever the drain is located. Combined with three to four inch walls around the side, the goal of your shower drainage plumbing is to get the water to flow to and down the drain.

You can physically build a collector for your new shower, but you really need to think about it. Do you really want to get into the complications of getting the sloping correct, not to mention making sure every aspect of it is waterproof? And I mean every aspect! It is much easier to simply buy a pre-cast collector online or at your local Lowes, Home Depot or hardware store. Building one might sound like a great idea, but you will probably feel differently after a couple of hours.

Regardless of how you go about getting a pan, you should make every effort to use one that has the drain located in the same spot as the original pan. Moving the drain pipes can be a task, particularly if the builder used a unique framing structure. If you are determined to move the drain, you are going to have to cut back the pipe or lengthen it, which may mean ripping up large chunks of the floor. Put another way, you are going to be looking at a multiple weekend project.

Assuming we have our drain lined up, the actual hook up is fairly simple. The drainage pipe should be facing vertical up to the collector. It will often look like a "U", which means it acts as a cleanout to keep nasty smells from coming back up from the drain. To connect the drain, you are going to create a water tight connection between a drain cap on the top of the pan and the drainage pipe. Systems vary, but you are typically going to do this by putting a coupling piece on the top of the drainage pipe. This is then covered with gaskets and literally screwed into the drain cap. The drain cap should act as a locknut, to wit, it screws directly onto the coupling.

The tricky part of this process is getting your drain cap to fit into a watertight position in the pan. This is accomplished by backing off the drain cap once you are sure everything fits together. At that point, you put plumbers putty around the underside of the cap and then screw it back on. The putty should form a tight seal between the cap and the shower pan, which keeps water from trickling under it and into the framing under the shower.

Obviously, bathroom showers come in a wide variety of styles these days. If you purchase a collector, they almost always come with plumbing instructions or the store can note anything unusual you should know. It sounds complex, but is typically pretty straight forward. Have fun!


Handling Your Own Shower Drain Installation Project


Plumbers Putty

BASKET STRAINER REPLACEMENT



Samsung Galaxy

Tube. Duration : 1.52 Mins.



BASKET STRAINER REPLACEMENT



Visit our website DunbarPlumbing.com or visit our Plumbing Forum http or contact us to schedule a service call at 859-359-4833

BASKET STRAINER REPLACEMENT

BASKET STRAINER REPLACEMENT


BASKET STRAINER REPLACEMENT

BASKET STRAINER REPLACEMENT

No URL BASKET STRAINER REPLACEMENT

Handling Your Own Shower Drain Installation Project


Samsung Galaxy
ItemTitle

Upgrading a bathroom is one of the more popular home improvement projects. Handling the plumbing for draining your shower can be exceedingly simple unless you go overboard.

Whether you are a bathtub or shower person, most people look for shower only options when buying a home. This simple fact means more than a few homeowners spend a weekend upgrading or installing showers in their bathrooms. Fortunately for you, it is a fairly simple process.

A collector or pan refers to the horizontal surface located at the bottom of the shower. The collector typically consists of a non-slip surface slightly banked towards the center or wherever the drain is located. Combined with three to four inch walls around the side, the goal of your shower drainage plumbing is to get the water to flow to and down the drain.

You can physically build a collector for your new shower, but you really need to think about it. Do you really want to get into the complications of getting the sloping correct, not to mention making sure every aspect of it is waterproof? And I mean every aspect! It is much easier to simply buy a pre-cast collector online or at your local Lowes, Home Depot or hardware store. Building one might sound like a great idea, but you will probably feel differently after a couple of hours.

Regardless of how you go about getting a pan, you should make every effort to use one that has the drain located in the same spot as the original pan. Moving the drain pipes can be a task, particularly if the builder used a unique framing structure. If you are determined to move the drain, you are going to have to cut back the pipe or lengthen it, which may mean ripping up large chunks of the floor. Put another way, you are going to be looking at a multiple weekend project.

Assuming we have our drain lined up, the actual hook up is fairly simple. The drainage pipe should be facing vertical up to the collector. It will often look like a "U", which means it acts as a cleanout to keep nasty smells from coming back up from the drain. To connect the drain, you are going to create a water tight connection between a drain cap on the top of the pan and the drainage pipe. Systems vary, but you are typically going to do this by putting a coupling piece on the top of the drainage pipe. This is then covered with gaskets and literally screwed into the drain cap. The drain cap should act as a locknut, to wit, it screws directly onto the coupling.

The tricky part of this process is getting your drain cap to fit into a watertight position in the pan. This is accomplished by backing off the drain cap once you are sure everything fits together. At that point, you put plumbers putty around the underside of the cap and then screw it back on. The putty should form a tight seal between the cap and the shower pan, which keeps water from trickling under it and into the framing under the shower.

Obviously, bathroom showers come in a wide variety of styles these days. If you purchase a collector, they almost always come with plumbing instructions or the store can note anything unusual you should know. It sounds complex, but is typically pretty straight forward. Have fun!


Handling Your Own Shower Drain Installation Project


Plumbers Putty

Bath bore Repair and alter 1 of 8



Samsung Galaxy

Tube. Duration : 8.00 Mins.



Bath bore Repair and alter 1 of 8



www.plumberx.comHello this is PlumberX. People always ask me what gave you the idea and what made you create these how to plumbing videos? Coming up with the idea was easy. After many years as a plumber and servicing customers at there home I've seen a lot of people in tuff situations, people that could not afford a plumber, people that didn't have time to wait for a plumber to come to there home and make repairs, hearing horror stories of Plumbers that have rip off costumers and gave bad service, to me this was a loud cry for help. One story come to mind; A friend of mine calls me and ask, PlumberX could you do me a favor and help this older lady that I know, and go by and look at her Plumbing, she needs plumbing work really bad but she's to scared to call a plumber because of the cost, and she know that if I send you over there to check out the plumbing she can trust me as a friend recommending you, sure I said I could do that. The next day came and I went to the older lady's home she came to the door with a pleasant smile very humble. I could see it in her eye's she didn't have to say a word ( What is this going to cost ) she was very polite and courteous. Sir would you like some thing to drink and I do appreciate you coming to check out my plumbing on such short notice. No problem mam, lets see what's going on here with your plumbing. This way Sir in the kitchen. As I walk through the home I saw in the corner of my eye younger children around 3, 5 and 6 years of age ...

Bath bore Repair and alter 1 of 8

Bath bore Repair and alter 1 of 8


Bath bore Repair and alter 1 of 8

Bath bore Repair and alter 1 of 8

No URL Bath bore Repair and alter 1 of 8

Where to Place Knobs on a Cabinet


Samsung Galaxy
ItemTitle

Once you decide to change out cabinet hardware you might find the style you pick won't look that great if you try and replace the knobs in the same spots that the old ones were in. Well what to do? You certainly don't want to go back to the same boring old hardware. Instead you need a better understanding of your options for where to place knobs on a cabinet.

The most obvious place to put a knob will be on a side opposite a hinge. The leverage allows you to open the door with almost no effort. This is great for those that might have a disability limiting their grip strength. The only exception to this rule is if you have roll out bottom cabinets, you know, the giant drawer types. Those you'll want to install the knobs centered on the cabinet to keep it from binding up on either side.

Well that gives you a rough idea of where to put the knobs but you probably need something a little bit more exact. Unfortunately there's no magic formula for where to place knobs on a cabinet. It's all going to come down to how the cabinets are designed and the size and shape of them and your kitchen.

There's a trick you can use to figure out where to place the knobs without just randomly drilling a bunch of holes into the cabinet face and hoping for the best. Head out to the hardware store and pick up a small tub of plumber's putty. Plumbers putty is a non-hardening compound that's slightly tacky. You can pull off little dollops of it then use it to just stick the knobs to the cabinet.

Here's what you'll do.

Open up the tub of Plumber's putty.

Pinch off a piece of putty about the size of the tip of your thumb.

Roll it into a ball.

Take the cabinet hardware and press the putty onto the back of it. Now you can just stick the knob onto the cabinet face wherever you think it will look right. Repeat this for a couple of the doors so you can get an overall feel for how the knobs will look sitting in a row. You can reposition the knobs just by popping them off the cabinet face and sticking them back on in a new spot.

Once you've figured out the right look for the cabinet you'll need to measure the knob offsets from the bottom and side edge of the cabinets. You can then use those measurements as a template for knob placement. Mark the offsets on each of the cabinets and double check to make sure they aren't slanting up or down.

The last thing to do is attach the hardware. Just drill the holes in the cabinet and slide a bolt through the hole and tighten the knobs down onto it. It's all a pretty simple job. Where to place knobs on a cabinet is a completely personal choice. You'll know what looks right once you get the knobs in position.


Where to Place Knobs on a Cabinet


Plumbers Putty

Installing A Kitchen Faucet



Samsung Galaxy

Video Clips. Duration : 15.07 Mins.



Installing A Kitchen Faucet



We were tired of not being able to control the water temperature in the kitchen. Since there were two handles, it was always too hot or too cold. A day before Christmas Eve we decided to install a new Kohler faucet before we had a lot more dishes to do.

Installing A Kitchen Faucet

Installing A Kitchen Faucet


Installing A Kitchen Faucet

Installing A Kitchen Faucet

No URL Installing A Kitchen Faucet




We were tired of not being able to control the water temperature in the kitchen. Since there were two handles, it was always too hot or too cold. A day before Christmas Eve we decided to install a new Kohler faucet before we had a lot more dishes to do.




Keywords:



Plumbers Putty

Where to Place Knobs on a Cabinet



Where to Place Knobs on a Cabinet
Where to Place Knobs on a Cabinet






Plumbers Putty


www.plumberx.comHello this is PlumberX. People always ask me what gave you the idea and what made you create these how to plumbing videos? Coming up with the idea was easy. After many years as a plumber and servicing customers at there home I've seen a lot of people in tuff situations, people that could not afford a plumber, people that didn't have time to wait for a plumber to come to there home and make repairs, hearing horror stories of Plumbers that have rip off costumers and gave bad service, to me this was a loud cry for help. One story come to mind; A friend of mine calls me and ask, PlumberX could you do me a favor and help this older lady that I know, and go by and look at her Plumbing, she needs plumbing work really bad but she's to scared to call a plumber because of the cost, and she know that if I send you over there to check out the plumbing she can trust me as a friend recommending you, sure I said I could do that. The next day came and I went to the older lady's home she came to the door with a pleasant smile very humble. I could see it in her eye's she didn't have to say a word ( What is this going to cost ) she was very polite and courteous. Sir would you like some thing to drink and I do appreciate you coming to check out my plumbing on such short notice. No problem mam, lets see what's going on here with your plumbing. This way Sir in the kitchen. As I walk through the home I saw in the corner of my eye younger children around 3, 5 and 6 years of age ...




Tags:



Plumbers Putty

Handling Your Own Shower Drain Installation Project



Handling Your Own Shower Drain Installation Project
Handling Your Own Shower Drain Installation Project






Plumbers Putty


Visit our website DunbarPlumbing.com or visit our Plumbing Forum http or contact us to schedule a service call at 859-359-4833




Keywords:



Plumbers Putty

Handling Your Own Shower Drain Installation Project



Handling Your Own Shower Drain Installation Project
Handling Your Own Shower Drain Installation Project






Plumbers Putty


www.plumberx.comHello this is PlumberX. People always ask me what gave you the idea and what made you create these how to plumbing videos? Coming up with the idea was easy. After many years as a plumber and servicing customers at there home I've seen a lot of people in tuff situations, people that could not afford a plumber, people that didn't have time to wait for a plumber to come to there home and make repairs, hearing horror stories of Plumbers that have rip off costumers and gave bad service, to me this was a loud cry for help. One story come to mind; A friend of mine calls me and ask, PlumberX could you do me a favor and help this older lady that I know, and go by and look at her Plumbing, she needs plumbing work really bad but she's to scared to call a plumber because of the cost, and she know that if I send you over there to check out the plumbing she can trust me as a friend recommending you, sure I said I could do that. The next day came and I went to the older lady's home she came to the door with a pleasant smile very humble. I could see it in her eye's she didn't have to say a word ( What is this going to cost ) she was very polite and courteous. Sir would you like some thing to drink and I do appreciate you coming to check out my plumbing on such short notice. No problem mam, lets see what's going on here with your plumbing. This way Sir in the kitchen. As I walk through the home I saw in the corner of my eye younger children around 3, 5 and 6 years of age ...




Tags: