Friday, September 14, 2012

How Plumbers Replace Bathroom and Kitchen Sink Faucets

How Plumbers Replace Bathroom and Kitchen Sink Faucets


If you are considering upgrading your bathroom and kitchen sink faucets, you have come to the right place. The following explanation will make your task much easier and will save your time as well.

How Plumbers Replace Bathroom and Kitchen Sink Faucets

How Plumbers Replace Bathroom and Kitchen Sink Faucets

How Plumbers Replace Bathroom and Kitchen Sink Faucets


How Plumbers Replace Bathroom and Kitchen Sink Faucets



How Plumbers Replace Bathroom and Kitchen Sink Faucets

However, before we start, make sure that you have following materials ready with you.

- New faucet assembly

- Basin wrench

- Adjustable wrenches

- Slip-joint pliers

- Scouring pad

Now follow these simple steps. (Assuming that you are replacing the old two-handled faucet with the more modern single-handled type)

Replacing Kitchen Sink Faucets
1. Before you start, go at the shut-off valves under the sink, and turn off the water.

2. Open the faucet so that it could drain any excess water.

3. The next step is to disconnect the hot and cold water supply lines from the shutoff valves. You can use a small adjustable-wrench to do this.

4. Reach up behind the faucet. You will find the coupling nuts that connect the supply tubes to the faucet. Unscrew the same using a basin wrench.

5. Behind the faucet, you will also find mounting nuts that hold the faucet in place. Remove these nuts using the same basin wrench.

6. Now that you have disconnected the mounting nuts, you can lift out the old faucet. Lifting it out, disconnect the sprayer hose from the assembly using an adjustable wrench.

7. Lift out the sprayer hose, and remove the faucet.

8. Once you have removed the faucet, clean the surface of the sink thoroughly with a scouring pad.

9. Remove the escutcheon cap and replace the same with the one that is included with your new faucet.

10. Now you are ready to make the new connection. Bring your new sprayer hose, and slip it down through the sprayer hole.

11. Feed the sprayer hose up through the center faucet hole, and connect the hose through the sprayer nipple using an adjustable wrench.

12. If the hot and cold supply tubes of the new faucet have a different length, attach flexible connectors to the fittings on the supply tubes. Hold the faucet fitting stationary with one wrench and tighten each connection with another wrench.

13. Insert and feed the supply lines and the connectors into the center hole, and then seat the faucet.

14. Now crawl up under the sink and in order to hold the faucet in place, install a washer and nut to the end bolts.

15. First, tighten the nuts by hand, and then with a basin wrench.

16. Connect the supply lines to the shutoff valves, and turn the water on.

17. Turn on the faucet and check for leaks.

Replacing Bathroom Sink Faucets
1. Go underneath the sink. Turn off the water. Loosen the collar nuts on the drainpipe.

2. Drain any excessive water, and then remove the drainpipe.

3. Loosen the nuts that hold the pop-up assembly in place under the sink using slip-joint pliers.

4. Unscrew the pop-up flange in order to free the assembly underneath the sink.

5. Remove the fittings that join the supply lines of the old faucet to the shutoff valves, using a wrench.

6. Repeat the steps 4-15 as explained above for replacing kitchen faucet.

7. Now, you have to install the pop-up assembly.

8. Push the pop-up rod down through the body of the faucet.

9. Attach the flat bar.

10. At the bottom of the new flange, use a little plumber's putty to hold the tailpiece so that the whole assembly protrudes up through the drain hole in the sink.

11. Spin the ring to position the same with the tailpiece under the sink.

12. In order to secure pop-up housing in place, tighten the nut on top of the tailpiece.

13. Hook up the pop-up lever onto the flat bar in order to secure it to the pop-up housing.

14. Drop the stopper into the drain hole.

15. Replace the drainpipe.

16. Tighten the collar nuts.

17. Turn on the faucet and check for leaks.

Hence, replacing a kitchen and a bathroom faucet is almost similar except for the work related to the pop-up assembly that is included with the bathroom sink.

How Plumbers Replace Bathroom and Kitchen Sink Faucets

Bath bore adjustment and alter 8 of 8 In HD

Bath bore adjustment and alter 8 of 8 In HD Video Clips. Duration : 5.67 Mins.


www.plumberx.comHello this is PlumberX. People always ask me what gave you the idea and what made you create these how to plumbing videos? Coming up with the idea was easy. After many years as a plumber and servicing customers at there home I've seen a lot of people in tuff situations, people that could not afford a plumber, people that didn't have time to wait for a plumber to come to there home and make repairs, hearing horror stories of Plumbers that have rip off costumers and gave bad service, to me this was a loud cry for help. One story come to mind; A friend of mine calls me and ask, PlumberX could you do me a favor and help this older lady that I know, and go by and look at her Plumbing, she needs plumbing work really bad but she's to scared to call a plumber because of the cost, and she know that if I send you over there to check out the plumbing she can trust me as a friend recommending you, sure I said I could do that. The next day came and I went to the older lady's home she came to the door with a pleasant smile very humble. I could see it in her eye's she didn't have to say a word ( What is this going to cost ) she was very polite and courteous. Sir would you like some thing to drink and I do appreciate you coming to check out my plumbing on such short notice. No problem mam, lets see what's going on here with your plumbing. This way Sir in the kitchen. As I walk through the home I saw in the corner of my eye younger children around 3, 5 and 6 years of age ...

Tags: